PAC 800 Specification Sheet

 

Fulfil so many places in the sheet as you know.
This sheet specifies the devices in order number___________________

Nominal battery voltage:_____________

Battery capacity _____________ and battery type:

_____ Sealed lead acid
_____ Unsealed lead acid
_____ else what?________________________________

Battery name or manufacturer name:____________________________________________________

Desired charging program is ___________ and code switch position is _________

Charging method:

_____ Cyclic charging (IUIo curve)
_____ Extended charging (Boosted charging) (IUUo curve)
_____ constant voltage charging (IU curve)

If device is used to give constant output then voltage should be __________________V and

current should be________A and absolute maximum output current must be limited to ________A

Serial number from earlier similar device_______________________________________

Output version:

_____ 12V (max 18V), 50A = model T
_____ 24V (max 36V), 30A = model N
_____ 36V (max 54V), 20A = model R
_____ 48V (max 72V), 15A = model P
_____ 72V (max 100V), 10A = model S

Mains cable:

_____ Normal cable and connector.
_____ Defa connector
_____ Calix connector
_____ Spiral mains cable

Enclosure version:

_____ Normal aluminium profile
_____ Normal aluminium profile with red colour
_____ Custom aluminium profile
_____ IP44 end covers
_____ Rack enclosure
_____ Multiple unit casing. ________PCS in one enclosure
_____ Multiple unit Rack casing. ________PCS in one enclosure
_____ Other modifications:
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________

 

Installed options (Select so many you want. Read from table1 possible combinations):

_____ Bus Output (BusOut)
_____ Bus Input (BusOut)
_____ Field pre-settable (trimmers for current and voltage set values) (Field)
_____ extra Status LED in rear panel (BLED)
_____ extra Status LED output with modular connector from rear panel (MLED)
_____ Battery temperature measurement (Temp)
_____ Sense cable input (measures voltage drop in output cables) (Sense)
_____ Drive protection relay (indicates mains cable connection) (Relay)
_____ Drive protection high side switch(indicates mains cable connection) (Switch)
_____ UPS battery charger (UPS)
_____ Analogy controlled device (9-pin D-connector): (Analog)
0-5V control means 0-_________ Voltage in output
0-5V control means 0-_________ Ampere in output

Accessories:
_____ 2*DIN-rail mounting springs
_____ Support frame (for wall mounting)
_____ Handle
_____ Battery temperature measurement and sense cables (fits with Temp/Sense option)
_____ Status LED at the end of cable (fits with MLED option)
_____ All 16 adjusted labels
_____ PCB varnishing

Table 1

This table shows which options are possible at the same time. If X then not possible. B
u
s
O
u
t		 B
u
s
I
n		 F
i
e
l
d		 B
L
E
D		 M
L
E
D		 T
e
m
p		 S
e
n
s
e		 R
e
l
a
y		 S
w
i
t
c
h		 U
P
S		 A
n
a
l
o
g		  
BusOut               x        
BusIn     x           x x x  
Field   x               x x  
Bled         x x x x   x    
Mled       x   x x x   x    
Temp       x x     x   x    
Sense       x x     x        
Relay x     x x x x   x      
Switch   x           x   x    
UPS   x x x x x     x   x  
Analog   x x             x    
                         

Other modifications:

________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________

 

POWERFINN OY
Perämiehenkatu 6
FIN-24100 Salo
Tel: +358 (0)2 777 290
Fax: +358 (0)2 777 2918
http://www.powerfinn.fi